News:

SMF - Just Installed!

Main Menu

River Firmware 2.60 Tuning Issue

Started by Andrewhburton, October 27, 2026, 04:59:39 PM

Previous topic - Next topic

Andrewhburton

I installed firmware 2.60 into my River yesterday. The tuning was worse than before. Before I go any further, I need to provide some background:

1. My River had been experiencing tuning issues prior to the update. It seemed to have trouble tuning itself properly after it had been unused for more than a week or two. I previously contacted Laurent who suggested I do a voltage test on the power supply. I had not yet done this when the issue seemed to resolve itself with more frequent usage. The tuning issues were not just between voices; there were issues with OSC1 and OSC2 being out of tune with each other, in degrees which varied from voice to voice, so no amount of fine tuning could get all the OSC1's and OSC2's in tune with each other. Again, this resolved itself somehow, so I never proceeded with any voltage testing.

2. I had been away for several weeks before installing the new firmware, and had neglected to check whether the previous tuning issues had returned during my absence. I had hoped the new firmware would take care of any issues.

So, having installed 2.60 and run the Learning routine, I got a message saying "Learning Success". The process took 82 minutes. Unfortunately the River was completely out of tune - both voice-to-voice and internally between OSC1 and OSC2. I ran a Fast Tune which did not help. I contacted Laurent again, and he gave me a set of instructions to follow to determine whether the problem is in the Learning routine or whether something else is wrong.

I will keep you all posted as I proceed. This process will take several days at least to complete.

Baloran

Thanks for your feedback, Andrewhburton.

It's baffling. On my The River—which is a pretty worn-out model since it's been used as a test bench—this new autotune has worked wonders. But this is actually the only unit I have on hand right now. So I'm counting on all of you for your feedback.

If you have a little time to devote to this issue, The River running version 2.60 can generate a log throughout the entire learning process that will explain what's happening.

I'm also thinking about another issue I've noticed on several "older" The River units. The power supply drifts—just a little, but it's enough to prevent the autotune from working.

I'll write up a guide explaining how to precisely monitor the voltages and how to adjust them ;)

I'm not too worried about it—we'll find a solution.

Andrewhburton

Per Laurent's instructions, today I started the River cold and immediately ran a new Learning routine. This time tuning took 80 minutes. The tuning was still bad. The voices themselves were out of tune with each other, and OSC1 and OSC2 were still out of tune with each other to varying degrees on each voice.

The next step tomorrow will be to do a fast tune at startup, then play while the instrument warms up.
If the tuning is still not good, I will then perform a test without Learning and go back to Autotune All.

I will report my results tomorrow.

Andrewhburton

Update:

I ran Laurent's test which captures the Learning data from the River as it tries to calibrate. The results confirmed that my voltages need adjustment. Laurent has provided us with instructions to perform this procedure. I will report back after it's done.

falconi

#4
Dear Laurent,

a possible bug in S+OTHER, found in OS 2.60 (not tried with earlier versions).
My RIVER is connected to a Windows 11 PC via USB, running Cubase 15.

3) DEST = Card Level or Card Feed, maybe also others, but not tried out
5) SRC = CC 11 Expr or CC 07 Vol, maybe also CC 04 Foot, but not tried out

After switching off THE RIVER, link between SCR and DEST does no longer seem to be working - nothing happens. 

Not helpful: Reloading the MULTI.

Helpful and a bit annoying workaround:
1. Selecting a (physically) internal SRC, like ModWheel and Aftertouch, maybe also Audio and Velocity (not tried).
2. Sending data on the the selected CC (e.g. by turning the internal ModWheel or pressing internal keys to send Aftertouch data) to try out the link, then re-selecting CC 07 or CC 11, then saving and reloading the MULIT.
Now working, but only until next power cycle. I'd like to have THE RIVER powering up in the same condition it has been before switching off.
Thank you.

QUESTION: Is there ANY WAY to make SINGLEs, MULTIs, LAYERs ... responsive to CC07 Volume, just to control the volume of sounds in the course of a song by midi controllers? 
Would appreciate that!
Thank you.

falconi.


Andrewhburton

Update on my River 1:

I can now say with confidence that I have solved the tuning issue.
I performed the voltage test according to Laurent's instructions. The only part I found difficult was actually applying the voltmeter probes to the connection points. They were recessed inside a multi pin connector and I was pretty reluctant to apply any pressure. But I did manage to get readings and the -15 V power supply was out of whack. I got a reading of -15.21 V, while the positive supply read 14.92 V. I was unable to get an exact Mirror Image value on the -15 V connector, but I got it to approximately -15 (with great difficulty making a connection), and decided to try and see if it were within the range of the Auto tune/learning capabilities. After clearing the tuning tables and running the learning routine, I found the tuning to be stable three days in a row, even when I was playing the instrument absolutely cold.

So thank you to Laurent for a much improved tuning system! I'm finally being reminded of how nice this instrument sounds.